That is usually accomplished via a CAT control cable from your computer to your radio which is completely separate from the Signalink.
Jt65 hf software#
The software must also be able to put your radio in transmit mode, and turn off trasmit mode. The 'Audio output device - Transmit' should be the device named 'Speakers (USB Audio CODEC ) which corresponds to the Signalink audio output device that sends the digital tones to your radio.Īll software programs that you use for digital modes MUST BE CONFIGURED TO USE THOSE DEVICES when you use the Signalink and all should work fine. The 'Audio input device - Receive' should be the device named 'Microphone (USB Audio CODEC ) which corresponds to the Signalink audio input device that captures the received audio signal from your radio. Here is a screen capture of the configuration dialog window: The sounds are pretty unique and easily identified. I really want to check out JT65 and Olivia modes.
HF clock and tones match spot on with 48/12 time sequence. You also need to choose the correct audio devices in the software for RX and TX, which was mentioned by another poster, and the software should see the audio from your radio. There is simply not allot of settings for JT65-HF so I am wondering if anyone can provide some points to what I might be doing wrong. This USB sound card will handle the Receive (RX) audio from your radio and deliver it to the software to be decoded, and send the transmit (TX) audio consisting of encoded tones from the software to your radio.
Jt65 hf driver#
The Signalink contains a USB sound card that will be a new sound device in your computer's Device Manager once the driver has been installed. The Signalink also needs to be plugged into a USB port on your computer using the supplied USB cable, and the driver for the Signalink must be installed on your computer for it to work properly. I have both a Signalink USB and a Rigblaster Pro.įor the Signalink to work, you need the correct Signalink cable that plugs into the back of your radio (I will assume that you have it, and it is plugged into the correct port on the back of your radio and into the RJ-45 jack on the Signalink). etc., so PLEASE DON'T GIVE UP! If what I tell you doesn't work, send me an email with a contact phone number (my email address is on QRZ.com for K4VBM) and I will be happy to call you and help you troubleshoot to get it working to pay it forward for my Elmer helping me. It can be very frustrating! Once you get the set-up right, all the digital modes should work, including PSK31, JT-65, RTTY, FT-8.
Jt65 hf update#
Nevertheless, it could use an update in the interface department.Don't panic or give up - you are bringing back my not so good memories of when I tried to get digital modes to work on my radio and computer - thank goodness I had an Elmer that got on the phone with me, and talked me through the set-up. The program does not put a strain on the computer’s performance since it does not require many resources in order to work properly, and the response time is good.Īll things considered, JT65-HF is a pretty handy piece of software, suitable to power users which are passionate about amateur radio. If you want to run something like DM780 and JT65-HF at the same time you. It is possible to call or answer a CQ, answer a caller and send a report, change the color map and adjust the brightness, contrast, speed and gain. The main category is Yaesu FT DX 3000 HF/50 MHz 100W Transceiver that is about.
Change color map, adjust audio gain and so onĪ raw decoder is available, and it possible to view logs in a separate window and clear it with just a click of the button, while the main window displays the current hour and date, enables you to view audio input levels and adjust the digital audio gain. In addition to that, you can add your PTT port and test it, call for a PSK Reporter or RB, add QRG and message definitions to an already existing list, and adjust the color-coded system.
Adjust multiple parametersįirst and foremost, at the first launch, you are met with the settings panel, so that you can configure all the options to fit your preferences.Īs a result, you can easily choose the sound input and output device from some drop-down menus, define a callsign, prefix, suffix and grid (4 or 6 characters), enable automatic RX/TX sample rate correction and select location of the RX/TX history file (CSV format). Moreover, there are no Help contents incorporated, which means that only experienced users will be able to find their way around this tool. Completing it brings you to a pretty cluttered interface, seeing that it consists of a menu bar, multiple buttons, several boxes and all kind of information all throughout the main window. You are required to go through a smooth setup process which is over in a jiffy. JT65-HF was built specifically as an amateur radio tool for receiving and transmitting the JT65A protocol, and comes packed with several predefined QRG (frequencies used by ham radio operators) and message definitions.